Image Map Image Map
  1. Announcement:
    Forum etiquette
    mbbrutman (Associate Cat Herder)
    May 12th, 2019
    Views:
    47,065
Page 1 of 3 123 LastLast
Threads 1 to 20 of 42

Forum: CP/M and MP/M

Discuss these venerable old operating systems and the machines that run them

  1. Sticky Thread Sticky: CP/M System Disks - Please Read

    Started by CP/M User, August 1st, 2006 10:24 PM
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 69,645
    April 19th, 2017, 11:19 AM Go to last post
  1. Epson Fx86e

    Started by Mike_Z, February 25th, 2021 09:28 AM
    • Replies: 4
    • Views: 82
    Today, 06:28 AM Go to last post
  2. 1982 British built LSI M-THREE computer restoration project

    Started by SteveH, September 8th, 2015 02:12 PM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 4,392
    February 25th, 2021, 01:27 AM Go to last post
  3. Relocator for Altiar 8K BASIC

    Started by alank2, February 24th, 2021 07:27 AM
    • Replies: 6
    • Views: 85
    February 24th, 2021, 01:51 PM Go to last post
  4. Softcard cp/m full screen editor

    Started by Wawavoun, February 23rd, 2021 11:36 AM
    • Replies: 2
    • Views: 85
    February 24th, 2021, 04:54 AM Go to last post
  5. Which version of the manual for Osborne 1

    Started by MikeP, February 22nd, 2021 10:05 AM
    • Replies: 2
    • Views: 43
    February 23rd, 2021, 10:00 AM Go to last post
  6. Floppy disk interwseave and SYSTEM load time

    Started by Mike_Z, February 16th, 2021 10:03 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 46
    • Views: 654
    February 23rd, 2021, 09:20 AM Go to last post
  7. Northstar Advantage 8/16 MSDOS

    Started by overCLK, February 20th, 2021 12:10 PM
    8088, msdos, northstar advantage
    • Replies: 0
    • Views: 59
    February 20th, 2021, 12:10 PM Go to last post
  8. Osborne 1 Keyboard Issue

    Started by confusedyeti, February 12th, 2021 12:53 PM
    • Replies: 1
    • Views: 59
    February 20th, 2021, 11:04 AM Go to last post
  9. Belts for Mitsubishi M-2894 8 inch floppy disk drives.

    Started by Chris42, February 17th, 2021 09:07 PM
    8 inch fdd, cp/m, s100
    • Replies: 2
    • Views: 63
    February 18th, 2021, 04:42 PM Go to last post
  10. Can CP/M possibly work on this

    Started by alank2, February 17th, 2021 07:16 AM
    • Replies: 7
    • Views: 194
    February 18th, 2021, 02:03 PM Go to last post
  11. Start a Kaypro Registry?

    Started by Mos6502, April 17th, 2011 05:53 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 5,181
    February 17th, 2021, 08:51 PM Go to last post
  12. Kaypro 4/84

    Started by Formulator, January 3rd, 2021 12:25 PM
    • Replies: 5
    • Views: 471
    February 17th, 2021, 12:55 PM Go to last post
  13. 8080 programming book recommendation

    Started by alank2, February 15th, 2021 03:06 PM
    • Replies: 5
    • Views: 124
    February 16th, 2021, 01:06 PM Go to last post
  14. Question Amstrad PCW8256 Not Reading Disk

    Started by CWP8256, February 15th, 2021 10:52 AM
    • Replies: 0
    • Views: 40
    February 15th, 2021, 10:52 AM Go to last post
  15. Programming

    Started by Mike_Z, February 9th, 2021 03:16 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 569
    February 13th, 2021, 03:31 PM Go to last post
  16. Ampro Little Board Plus and SmartWatch

    Started by Alphasite, February 6th, 2021 07:57 PM
    • Replies: 2
    • Views: 147
    February 7th, 2021, 05:01 PM Go to last post
  17. Kermit 80

    Started by Mike_Z, January 29th, 2021 12:50 PM
    9 Pages
    1 2 3 ... 9
    • Replies: 81
    • Views: 1,767
    February 6th, 2021, 02:12 PM Go to last post
  18. ZCPR3 for Montezuma CP/M on TRS-80 M4

    Started by vldmrrr, February 3rd, 2021 01:40 PM
    • Replies: 8
    • Views: 260
    February 5th, 2021, 11:04 AM Go to last post
    • Replies: 4
    • Views: 189
    February 3rd, 2021, 12:57 PM Go to last post
  19. 25 pin keyboard?

    Started by SMichelsen, July 2nd, 2019 09:51 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 37
    • Views: 5,729
    February 2nd, 2021, 04:59 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •