Image Map Image Map
  • m_thompson's Avatar
    July 14th, 2019, 09:06 AM
    m_thompson replied to a thread New to me PDP-11/53 in DEC
    That is the CPU that I have. The Dataram board has 4x columns of 18 RAM chips. The RAM chips are Micron 1259-12, so that makes it 1MW with parity...
    7 replies | 284 view(s)
  • m_thompson's Avatar
    July 14th, 2019, 06:25 AM
    You can find the manuals for the 8/e here: http://www.bitsavers.org/pdf/dec/pdp8/pdp8e/ You can start by removing all of the boards and testing...
    1 replies | 100 view(s)
  • m_thompson's Avatar
    July 14th, 2019, 06:18 AM
    m_thompson replied to a thread PDP-9 at the RICM in DEC
    Too many visitors yesterday to get much done on the TC02. We are still getting the END error after we send a MOVE command to the TC02 and the tape...
    62 replies | 7786 view(s)
  • m_thompson's Avatar
    July 11th, 2019, 03:08 PM
    Vincent made replacement switch and lamp PCBs for the 8/I. http://so-much-stuff.com/pdp8/frontpanel/frontpanel.php
    159 replies | 13636 view(s)
  • MattisLind's Avatar
    July 8th, 2019, 01:41 AM
    Here is the scan: http://storage.datormuseum.se/u/96935524/Datormusuem/DEC/MAINDEC-08-DIVTC-A-D_VT55_ACCEPTANCE_TEST.pdf Add the binary later on....
    13 replies | 713 view(s)
  • m_thompson's Avatar
    July 7th, 2019, 04:48 PM
    m_thompson replied to a thread PDP-9 at the RICM in DEC
    We replaced a defective S107 inverter FlipFlop. The control signals to the TU55 DECtape look better, but we are still getting the END error and the...
    62 replies | 7786 view(s)
  • m_thompson's Avatar
    July 7th, 2019, 05:31 AM
    m_thompson replied to a thread PDP-9 at the RICM in DEC
    We tried to control the TU55s through the controller. If we command the drive to move, it moves about 1mm, stops, and shows an END error. It thinks...
    62 replies | 7786 view(s)
  • m_thompson's Avatar
    July 7th, 2019, 05:21 AM
    m_thompson replied to a thread New to me PDP-11/53 in DEC
    How do I tell which version I have? I have an Emulex UC07 Dual-SCSI that I could use. I should have more memory boards too. I need to...
    7 replies | 284 view(s)
  • m_thompson's Avatar
    July 6th, 2019, 07:20 AM
    m_thompson started a thread New to me PDP-11/53 in DEC
    I picked up a BA23 based PDP-11/53 yesterday that I removed from an Ultratech wafer stepper system. It lived all of its life in a clean room, so...
    7 replies | 284 view(s)
  • m_thompson's Avatar
    July 6th, 2019, 05:30 AM
    This will help: http://www.ultimate.com/phil/pdp10/dec.disks The manual for the RF09 for the PDP-9 was first printed in July of July of 1970, so...
    5 replies | 185 view(s)
  • MattisLind's Avatar
    July 5th, 2019, 12:27 AM
    Good work getting the 4907 working and a really nice 4054! I would like to somehow emulate the 4907. Did you do any work on this or is it me...
    14 replies | 303 view(s)
  • m_thompson's Avatar
    July 3rd, 2019, 09:17 AM
    You have an early 8/e. On the later ones the first switch position is at about 11:00 and the last at about 7:00.
    4 replies | 101 view(s)
  • m_thompson's Avatar
    July 3rd, 2019, 03:35 AM
    There have been several sold on eBay recently, but they were quite expensive.
    1 replies | 92 view(s)
  • m_thompson's Avatar
    July 2nd, 2019, 03:46 AM
    m_thompson replied to a thread what switch panel is this? in DEC
    It might be from a PDP-8a. The third LED is for Battery Charge.
    9 replies | 352 view(s)
  • m_thompson's Avatar
    July 1st, 2019, 12:41 PM
    m_thompson replied to a thread PDP-9 at the RICM in DEC
    Several of the Margin Power switches were on, and we didn't have the Margin Power Supply cable installed, so there were unpowered sections of the...
    62 replies | 7786 view(s)
  • MattisLind's Avatar
    June 30th, 2019, 04:04 AM
    I have a PDP-8 Maindec. VT55 acceptance test. Both paper tape and listing. http://www.datormuseum.se/documentation-software/paper-tapes I can...
    13 replies | 713 view(s)
  • m_thompson's Avatar
    June 25th, 2019, 04:20 AM
    How about a quad board with a KT8A and 128kw of RAM, and other peripherals.
    20 replies | 1232 view(s)
  • m_thompson's Avatar
    June 24th, 2019, 04:01 PM
    m_thompson replied to a thread PDP-9 at the RICM in DEC
    Looks like the S107 module in the TC02 inverts two of the device address bits from the processor. One of the inverted bits is inactive, so the next...
    62 replies | 7786 view(s)
  • MattisLind's Avatar
    June 24th, 2019, 12:17 PM
    I have a bunch of Signetics N8X305 that I am unlikely to ever use. Pulls from circuit boards. Give me an offer to consider!
    7 replies | 309 view(s)
  • m_thompson's Avatar
    June 24th, 2019, 03:58 AM
    Roland, An combination I/O card that included RTC, two serial, Centronics printer port, memory, and bootloader would be really great. It would...
    20 replies | 1232 view(s)
  • m_thompson's Avatar
    June 23rd, 2019, 03:50 PM
    m_thompson replied to a thread PDP-9 at the RICM in DEC
    We connected up the I/O cables from the PDP-9 processor to the TC02 and borrowed the indicator display cables from the TC59 controller. When...
    62 replies | 7786 view(s)
  • m_thompson's Avatar
    June 23rd, 2019, 03:49 PM
    m_thompson replied to a thread PDP-9 at the RICM in DEC
    I could only find Dialight 507-397-1475-600 replacements. The originals are flush with the front panel. The replacements stick out about 1/8".
    62 replies | 7786 view(s)
  • m_thompson's Avatar
    June 23rd, 2019, 05:34 AM
    m_thompson replied to a thread PDP-9 at the RICM in DEC
    The original power supply in the I/O cabinet for the TC59 Magnetic Tape controller didn't have enough power to also feed the TC02 DECtape controller....
    62 replies | 7786 view(s)
No More Results
About MattisLind

Basic Information

Age
48
About MattisLind
Location:
Stockholm, Sweden

Signature


Statistics


Total Posts
Total Posts
668
Posts Per Day
0.32
General Information
Last Activity
July 13th, 2019 11:04 AM
Join Date
September 29th, 2013
Referrals
0
Home Page
http://www.datormuseum.se

1 Friend

  1. m_thompson m_thompson is offline

    Senior Member

    m_thompson
Showing Friends 1 to 1 of 1