Image Map Image Map
Tab Content
  • cbscpe's Avatar
    Today, 03:52 AM
    cbscpe replied to a thread New Version of RLV12 Emulator in DEC
    Ok fixed the download folder content and also found a better place in www.microchip.com which provides links to the various software. Let me know if...
    12 replies | 1049 view(s)
  • cbscpe's Avatar
    Yesterday, 12:48 PM
    cbscpe replied to a thread New Version of RLV12 Emulator in DEC
    I just updated the download section with a RLV12 Emulator V2.0 post. You can download all files.
    12 replies | 1049 view(s)
  • cbscpe's Avatar
    Yesterday, 12:46 PM
    cbscpe replied to a thread PDP SBC - J11 Hack in DEC
    Hi Stephan, The designs are available, as Eagle 7.5 files and as Gerber files. Peter
    177 replies | 28741 view(s)
  • cbscpe's Avatar
    January 24th, 2020, 02:32 AM
    cbscpe replied to a thread New Version of RLV12 Emulator in DEC
    Hi Leon, Thanks. I'm currently preparing the download page for the RLV12 V2 Emulator and will include all files, i.e. Eagle, Gerber, ASM...
    12 replies | 1049 view(s)
  • cbscpe's Avatar
    January 20th, 2020, 06:46 AM
    cbscpe replied to a thread Rt-11 sysgen in DEC
    The following was working for me COPY/SYS .SYG .SYS without asterisks.
    2 replies | 238 view(s)
  • cbscpe's Avatar
    January 12th, 2020, 10:56 PM
    What you need to know how each controller allocates units to its attached disks and which is the starting LUN. In the case of the RQDX this is well...
    4 replies | 242 view(s)
  • cbscpe's Avatar
    January 12th, 2020, 11:28 AM
    Good news. I was able to do a sysgen of a RT-11 system with two MSCP controllers and finally learned how this thing with units, ports and partition...
    9 replies | 921 view(s)
  • cbscpe's Avatar
    January 11th, 2020, 12:10 PM
    Ok found it, apparently you have to boot after you have changed the settings of an individual unit .show dev:du Device Status ...
    4 replies | 242 view(s)
  • cbscpe's Avatar
    January 11th, 2020, 09:45 AM
    I have done a RT-11 SYSGEN and added a second MSCP DU controller (ports=0). However, I don''t know how to talk to the second MSCP controller. In...
    4 replies | 242 view(s)
  • cbscpe's Avatar
    January 11th, 2020, 03:50 AM
    cbscpe started a thread Rt-11 sysgen in DEC
    In the sysgen manual it says "Then rename the SYG files (monitors and handlers) to SYS. You can also rename the monitor to distinguish it from...
    2 replies | 238 view(s)
  • cbscpe's Avatar
    January 10th, 2020, 12:07 PM
    This system has been used in a mushroom (champignons) farm. That's all I could investigate. I was thinking about doing a RT-11 SYSGEN using SIMH with...
    9 replies | 921 view(s)
  • cbscpe's Avatar
    January 10th, 2020, 12:01 PM
    cbscpe replied to a thread DLV11J Line Driver in DEC
    Thanks, I suppose the DLV11J brand is not important, as long as these are the same ICs they are probably used the same way. Yes all lines are...
    2 replies | 205 view(s)
  • cbscpe's Avatar
    January 9th, 2020, 12:51 PM
    cbscpe started a thread DLV11J Line Driver in DEC
    On my Plessey DLV11J the line drivers ICs some UA9636 get rather hot as well as the DS0026 which is used to generate -12V are getting rather hot when...
    2 replies | 205 view(s)
  • cbscpe's Avatar
    December 29th, 2019, 10:09 AM
    cbscpe replied to a thread PDP-11 Hack complete in DEC
    Over the past few days I have done some cleanup and changes to the CPLD design files and the microcontroller firmware for the various cards of my...
    14 replies | 2841 view(s)
No More Results
About cbscpe

Basic Information

Age
61
About cbscpe
Location:
Switzerland
Occupation:
Seniour Network Engineer

Statistics


Total Posts
Total Posts
266
Posts Per Day
0.26
Albums
Total Albums
1
Total Photos
7
General Information
Last Activity
Today 03:53 AM
Join Date
April 11th, 2017
Referrals
0