Image Map Image Map

Search:

Type: Posts; User: rittwage

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    21
    Views
    1,363

    There was no NTSC 128D sold like this in the US...

    There was no NTSC 128D sold like this in the US or Canada, so this is some kind of production sample or development machine that was never mass produced. They shipped the metal DCR instead in North...
  2. Replies
    3
    Views
    284

    High pitch noise is of course something vibrating...

    High pitch noise is of course something vibrating quickly. Most likely is a coil somewhere, and usually they are dampened by a bit of glue. I would check the monitor board or power supply for them.
  3. Replies
    5
    Views
    315

    I'll take it if any other deals fall through.

    I'll take it if any other deals fall through.
  4. Every Amiga 1000 owner got Kickstart/Workbench...

    Every Amiga 1000 owner got Kickstart/Workbench with the machine, and I'm pretty sure 1.1, 1.2, and 1.3 were all free upgrades from the dealer. I don't think it was ever sold.

    Owning an Amiga 1000...
  5. Lower your price and someone may take you up on...

    Lower your price and someone may take you up on it. You are a somewhat high...
  6. Replies
    0
    Views
    72

    Wanted: Fat Agnus (Any version)

    Hello,

    I have recently resurrected an old Rev5 A500. *all* of the RAM chips were bad... 12 were shorted, the other 4 were blown. I don't know what happened to it, but I suspect maybe someone used...
  7. I think the timing is funny sometimes even on the...

    I think the timing is funny sometimes even on the original keyboard. Some conditions cause it to stop working sometimes.

    I always hold CTRL-APPLE then press and hold reset for a moment, then let...
  8. Replies
    29
    Views
    966

    Wow- nice! It's even a 16K... That's very early...

    Wow- nice! It's even a 16K... That's very early and not upgraded. Unusual...
  9. Replies
    3
    Views
    204

    Have you tried just pulling the KBRESET pin on...

    Have you tried just pulling the KBRESET pin on the keyboard connector low to see if it resets? (or high, I haven't looked at schematics). I would do it with at least a 1K resistor to be safe.
  10. There was a class action lawsuit settled in 2005...

    There was a class action lawsuit settled in 2005 where Audigy customers unhappy with their purchase could get a 25% discount. I got the letter....
  11. Replies
    12
    Views
    787

    Sorry, yes that adapter will work. No, you can't...

    Sorry, yes that adapter will work. No, you can't boot from external without modifying the Amiga internally. You can pull up the drive select pins from one of the VIA chips and attach to a DPDT switch...
  12. Replies
    13
    Views
    992

    I believe if using the original floppy cable with...

    I believe if using the original floppy cable with pulled pins, the ID jumpers on the drive must ALL be set on, not NONE of them. That way it can respond to whatever ID the cable tells it to. The way...
  13. Replies
    31
    Views
    1,424

    I don't know. Unless you are fibbing a little and...

    I don't know. Unless you are fibbing a little and you really think it is an investment, just undo your board to Rev0 specs if you really want that 1977 feeling.

    However, you know everyone...
  14. Drying cap(s) or maybe cold solder joint......

    Drying cap(s) or maybe cold solder joint... Probably the former.
  15. Replies
    16
    Views
    989

    That's about all mine ever did, either - almost...

    That's about all mine ever did, either - almost exactly. I sold it to another member here... Hopefully someone can repair them.
  16. It is on the installer disk, but does not...

    It is on the installer disk, but does not "install" it for you. Go figure... Copy it from the 3.1 installer disk to "C:" and it should work.
  17. Replies
    12
    Views
    787

    3.5" drives are all 80-tracks whether DD or HD,...

    3.5" drives are all 80-tracks whether DD or HD, so no double-stepping. However, some drives don't work in DD mode very well- the older the better for this support.

    You can always get an external...
  18. Thread: Model 3 Plus

    by rittwage
    Replies
    11
    Views
    1,001

    I had a model 4 with 80-track drives and it was a...

    I had a model 4 with 80-track drives and it was a pain since no "normal" disks work.

    I was able to create them with a PC drive and the "emulator pointing to the real disk drive" trick with the...
  19. Replies
    28
    Views
    4,782

    Yes, that is what I did in the past, but they...

    Yes, that is what I did in the past, but they seem to be very delicate and often the connections break on the socket pin connector, so I stopped doing it. :)
  20. Replies
    28
    Views
    4,782

    Here is a photo of the latest built kit. I have...

    Here is a photo of the latest built kit. I have only one left if Torfinn gets one. I am out of VGA connectors, so the last one will have composite only, which is fine for old mono monitors or even a...
  21. Replies
    28
    Views
    4,782

    I would say $14.25 plus the 20% discount if I...

    I would say $14.25 plus the 20% discount if I ship from Paypal, so $11.40 or so. If it is less I will take care of it.
  22. Replies
    28
    Views
    4,782

    It looks like First Class International is $14.25...

    It looks like First Class International is $14.25 on the website, but I know it's been less when I actually ship it in the past (by more than $5)
  23. Replies
    10
    Views
    928

    Put me on the list for an updated one, David.

    Put me on the list for an updated one, David.
  24. Replies
    10
    Views
    928

    I built some of those many years ago, and...

    I built some of those many years ago, and actually sold a few kits to users on this site. It works but is very limited.

    Some others have added some functionality and buttons and continued the...
  25. Thread: Ibm 5150

    by rittwage
    Replies
    6
    Views
    794

    That's a really nice one, and shouldn't be a ton...

    That's a really nice one, and shouldn't be a ton of work to get running. Good luck!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4