Image Map Image Map

Search:

Type: Posts; User: inotarobot

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    64
    Views
    6,792

    Flpppy Drive alignment

    I am wondering if the Moderator would consider moving this whole post across to a different forum section since many different machines have floppy drives, not just "PC's and Clones"

    May I suggest...
  2. Replies
    64
    Views
    6,792

    This is an interesting brief manual for the...

    This is an interesting brief manual for the DYMEK alignment disks.

    I dont see it on BITSAVERS so maybe it could be added at some point.

    http://www.myatari.com/dymekalign.pdf
  3. Replies
    64
    Views
    6,792

    Helpful thanks.

    Helpful thanks.
  4. Hi Roland, Great to hear you found the manual...

    Hi Roland,

    Great to hear you found the manual and prog. and that it still works. Well done

    Maybe this info can also be added to BITSAVERS.org Test Equipment
  5. Replies
    64
    Views
    6,792

    Interesting machine. So little info about it...

    Interesting machine. So little info about it comes upon a Google search. Guess it was a special made using a modified Olivetti PC machine ?
  6. Replies
    64
    Views
    6,792

    I think this was actually a good thread to...

    I think this was actually a good thread to rebirth. Thanks for those adding their valuable input to it.
  7. Replies
    64
    Views
    6,792

    Hi Chuck, Can you provide that Z80CPM code...

    Hi Chuck,

    Can you provide that Z80CPM code then please? Maybe put on BITSAVERS somewhere suitable?

    the 5 1/4" Dysan Alignment Disks I have are hand marked Digital Alignment Disks

    224/2A s/n...
  8. Gorgeous Floppy Disk Controller PCB - SMS model FD0303 for IBM 3740 PERTEC FD400

    Hi all,

    As I was getting out my Floppy Drive alignment Disks, I had the early Floppy Disk Controller card stored with them.

    I had partly forgotten about it so I brought it up to the house and...
  9. It may have been

    It may have been
  10. Hi again Tony, this wonderful system is...

    Hi again Tony,

    this wonderful system is currently in storage in my 40ft storage semi-trailer that's parked at a remote location to my home.

    My Saab 9-5 car just blew a head gasket 3 days back...
  11. Hi Tony, I thought I had uploaded the eprom...

    Hi Tony,

    I thought I had uploaded the eprom images to Bitsavers.org either under the Computing archive group, as code for CSA. But there not there.These would have been the eproms for the ...
  12. Replies
    64
    Views
    6,792

    ok I am rebirthing this old thread as I need to...

    ok I am rebirthing this old thread as I need to do some floppy drive testing. Chuck I found this post of yours very informative. Also Dwight's post mentioned.

    20+ years back I bought brand new a...
  13. Jumper setting of 5.25" Teak FD-55GFR 149U for FC5025 USB 5 1/4" floppy adaptor pcb

    Hi all,

    I am trying to set up a Teac 5 1/4" floppy drive to a FC5025 USB 5 1/4" floppy adaptor pcb made by http://www.deviceside.com/fc5025.html

    So far looking at the uTube videos about FC5025...
  14. Quick note prior to bed, Monitor one is...

    Quick note prior to bed,

    Monitor one is labelled 'Archimedes' on LH lower front corner

    label on back says 28-AKF11- 2000113 220-240V 50hz 75w Made in Taiwan Manufactured for ACORN Computers...
  15. I need to clarify part of the statement from my...

    I need to clarify part of the statement from my recent post being:-

    re "........despite getting "some flack" for the 15min diversion into and back out, by Maria whom I was taking...
  16. Update on the these two monitors. Today,...

    Update on the these two monitors.

    Today, Friday, I found myself driving past the eWaste site, so despite getting "some flack" for the 15min diversion into and back out, by Maria whom I was taking...
  17. Hi Brian. Thank you for that clear...

    Hi Brian.

    Thank you for that clear clarification. It makes a lot of sense.

    A quick point I had made was both monitors has the leads that are at the back of case cut off almost flush.
    In both...
  18. Thank you. My APOLOGIES if I may have or will in...

    Thank you. My APOLOGIES if I may have or will in future offend anyone reading this post saying 'nobody cares' as that was NOT my intent.

    I realize that anyone that joins or infact reads VCFED...
  19. Brian, thank you for your reply I had written...

    Brian, thank you for your reply I had written the original message in haste and as it was I was unable to get back to the eWaste place the next day so I think these 2 early CRT monitors would have...
  20. guess no one here cares about the fate of very...

    guess no one here cares about the fate of very early crt monitors going to eWaste.
  21. noticed 2 Vintage CRT Monitors at my local eWaste, aus$10, should I have bought them?

    Hi all

    just before closing, I noticed 2 smallish Vintage CRT Monitors at my local eWaste, aus$10, should I have bought them?

    One was badged Amstrad on front. It had 2 leads out back, sadly both...
  22. Well I have sent the Japanese seller a few...

    Well I have sent the Japanese seller a few messages, all in english.

    Then I decided to use google translator to send a polite detailed message in Japanese.

    Over a week now and still NO answer....
  23. Yes, I think it's maybe the eBay Shipping...

    Yes, I think it's maybe the eBay Shipping Calculator. I have had lots of items sent in years gone by, that turns out way cheaper shipping than eBays quoted price.

    However, it does initially put...
  24. I will go and take screen shots in the next few...

    I will go and take screen shots in the next few hrs and post.


    I think it mostly the usa sellers using Couriers with express shipment for International packages. verses usps cheap parcel service
  25. why is it the only seller on ebay that has what you need has a bad reputation

    Hi all,

    Ok, this is sort of a rant.

    I am trying to update my soldering tools to cope with doing the tiny surface mount components.

    Over the years I have always bought TOP Brand tools, no...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4