Image Map Image Map

Search:

Type: Posts; User: alejack12001

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. To the responder Svenska, the messages I received...

    To the responder Svenska, the messages I received initially using telnet on the AT&T were strange as the Win 2K machine seemed to look for NTLS from the sender. The exact message was "Error NTSL not...
  2. Chuck, you mentioned a Linux based network. I am...

    Chuck, you mentioned a Linux based network. I am a little confused by that statement. Most home networks are Linux in general if you're using OpenWRT or DDWRT.

    I tried to stand up a telnet session...
  3. Replies
    1
    Views
    99

    Seeking VNC for 8086 DOS computer

    Has anyone used a VNC for DOS on an 8086 machine? If so, please let me know what works.
  4. The creation of the mtcpcfg file was a success in...

    The creation of the mtcpcfg file was a success in generating the IP address and other data for the config using the dhcp executable. I used the ping and was surprised to see it worked. I tried...
  5. I wanted to let Chuck(G) and everyone else that I...

    I wanted to let Chuck(G) and everyone else that I had success today in getting the AE-2/C and the AUI to work with the AT&T 6300. Chuck(G): the changes you sent for the I/O addressing schema and the...
  6. First, after several tries, I found my AE-3 is...

    First, after several tries, I found my AE-3 is not an AE-3 but an AE-2/C. There is a label on the reverse side with the following data: PCB, AE-2/C ISA REV f, and bar code A2X0419086. The pictures on...
  7. It's possible that the AE-3 I have is in fact...

    It's possible that the AE-3 I have is in fact AE-2s. I'd have to find a switch manual similar to the AE-3 I have t make a comparison. I don't know if the settings would be different as well.
  8. You wrote

    You wrote <If you have an AE3, why not use the RJ45/10BaseT connection?> The card doesn't have an ethernet connector. Please refer to an earlier post where I put up a picture of the card in question....
  9. Chuck(G): I just want to clear about what you...

    Chuck(G):

    I just want to clear about what you wrote, <the PROM is for network booting--you don't need it and the jumper block just below it should have no jumpers on it.> Are you referring to W9...
  10. Chuch(G): does your AE-3 manual have a block...

    Chuch(G): does your AE-3 manual have a block diargam that may explain it's componets? I'd like to know what that big VLSI chip is for and what the ROM if it was there respresnts.
  11. Your right, for some reason I didn't preconfigure...

    Your right, for some reason I didn't preconfigure the card before inserting it into the machine, my bad. I'll reconfigure it and try again. According to Checkit, IRQ 3 is available as is D000h for...
  12. I put the network card in today and ran into an...

    I put the network card in today and ran into an immediate problem with my hard drive and floppy controllers. The hard drive, which had been booting the system prior to the insertion of thhe network...
  13. Okay, I wasn't sure if the included binary was...

    Okay, I wasn't sure if the included binary was for the added ASM or not. Thank you for telling me this about the package.
  14. Thank you for the ASM code associated with the...

    Thank you for the ASM code associated with the Novell. I have a question regarding the code and its application. I have acquired MSAM 3.0 to compile the ASM code on the AT&T. If there is success in...
  15. I thank you for the input. Yes, I did ask about...

    I thank you for the input. Yes, I did ask about the arguments for the NE2000. According to Artisoft AE-3 data and switch sheet here is a limited number of addresses available for the I/O. I have to...
  16. two questions: regarding the NE2000 driver first,...

    two questions: regarding the NE2000 driver first, are there arguments assocated with the 1993 driver? Second, I am using MSDOS 6.22 on the AT&T. Network commands such as ping, ipconfig, telnet, ftp,...
  17. Chuck(G) did you use the 32K or 8k base memory...

    Chuck(G) did you use the 32K or 8k base memory select on your 6300 for the Artisoft AE-3?
  18. Thanks to all who expressed a suggestion,...

    Thanks to all who expressed a suggestion, however, I decided to follow Chuck(G) and Trixter's advice and acquire the Artisoft AE-3 based on Chuck's jumper recomendation over installing software....
  19. Sorry about the data mix up, I was looking at...

    Sorry about the data mix up, I was looking at their picture of the Artisoft AE-3. I have reviewed the manual and 8-bit is supported through jumpers as was suggested. Thank you both for the...
  20. Trixter: Would a 3-comm 16-bit work with AT&T?

    Trixter:

    Would a 3-comm 16-bit work with AT&T?
  21. Chuck: I looked up the Artisoft AE-3 and found...

    Chuck:

    I looked up the Artisoft AE-3 and found only 16-bit. Did you recall if yours was a 16-bit card or 8-bit? Can a 16-bit card work in the 6300? If I did get this card, where would I find the...
  22. Seeking 8-bit etherent card that will work with AT&T 6300

    What brand\type of Ethernet card will work in AT&T 6300?
  23. Replies
    68
    Views
    77,290

    I wanted to give you all an update regarding the...

    I wanted to give you all an update regarding the posting conducted last summer with the Paradise video card and the color situation that was discssed. The removale of the 12th pin on the VGA cable...
  24. The GoTek software I am using is version 1.40i...

    The GoTek software I am using is version 1.40i from ipcas.com. I know there is an earlier version of the software, version 1.31T, however, I found it buggy. As for the PROM inside of the GoTek, I...
  25. You both were right about the use of the DS1 as...

    You both were right about the use of the DS1 as the identifier for the system that a 1.44 floppy is there. The Floppy emulator is connected to the end of the twisted cable. The new problem has...
Results 1 to 25 of 73
Page 1 of 3 1 2 3