Image Map Image Map

Search:

Type: Posts; User: Dwight Elvey

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    24
    Views
    433

    I have the design. It was just that I don't have...

    I have the design. It was just that I don't have plans to make any more. It was just a one time shot to help spread the cost.
    As has been said, the 6530 had a mask ROM that was application specific....
  2. Replies
    24
    Views
    433

    Back to the original KIM-1. I would never think...

    Back to the original KIM-1. I would never think of the use of a KIM-1 for such a purpose, when there are many other methods of doing this type of project. An Arduino or similar would be fine. The...
  3. Replies
    13
    Views
    200

    Both Nvidia and AMD clearly misread the demand....

    Both Nvidia and AMD clearly misread the demand. AMD, needs to keep a tight ship. They need to order wafers far in advance and substrate silicon is tight now as well. When Intel was leading, they...
  4. Replies
    21
    Views
    197

    Ah! Mike to the rescue again. Thanks for coming...

    Ah! Mike to the rescue again. Thanks for coming in.
    Early S100 was a mess.
    Dwight
  5. Replies
    21
    Views
    197

    Hi It is a CMP M, not CPI. see may last updated...

    Hi
    It is a CMP M, not CPI. see may last updated #4 post. For the reset, you can disassemble the binary.
    All register moves are MOV. The 8080 for loading register pairs is LXI rp, ####.

    Dwight
  6. Replies
    21
    Views
    197

    I missed CPD. It is another of the memory to...

    I missed CPD. It is another of the memory to memory.loop
    loop2
    MOV A,M
    DCX HL
    XCHG
    CMP M
    JNZ Error
    DCX HL
    XCHG
    DCR C
  7. Replies
    21
    Views
    197

    Hi Hugo It looks like the binary would run on a...

    Hi Hugo
    It looks like the binary would run on a 8080. I don't think I see anything that is specific to Z80.
    Dwight

    Ops I see LDIR
    That isn't in a 8080. You'll need to code that. It reads data...
  8. Replies
    13
    Views
    200

    Current day graphic and processor have built in...

    Current day graphic and processor have built in test circuits that constantly monitor the edge of failure. They constantly readjust to keep the part at close to maximum operation. Most all of the...
  9. Electrolytics that have been sitting for a long...

    Electrolytics that have been sitting for a long time should be brought up to voltage slowly. It is because of the way they work. You power them up fast and they have to vent. Normally the seals are...
  10. It is likely one that uses DSKRDY* signal as...

    It is likely one that uses DSKRDY* signal as well.
    Dwight
  11. Replies
    155
    Views
    12,646

    Hi It has taken me a little while to catch up....

    Hi
    It has taken me a little while to catch up. First, you should always print a copy of the data sheet of the device you are looking at so you know what is happening. I'm going back to post 135...
  12. I've seen that before. It is the material that...

    I've seen that before. It is the material that was used that had a void. In the void it has some acid or salt. The water will defuse through the material. Since the water coming in has a lower...
  13. This sounds like a problem I've seen. Do the...

    This sounds like a problem I've seen. Do the envelopes have a white liner? If so it may be the adhesive that is suppose to hold the liner in the envelope that is failing. When it does, it leaks...
  14. Replies
    28
    Views
    1,133

    Ok, wind a coil. It looks like the primary and...

    Ok, wind a coil. It looks like the primary and secondary are a 1:1 and the feedback coil is 4:1, or 1/4 of the primary.
    Something like 24 turns for the primary and secondary with a 6 turn feedback....
  15. If it is turning orange and getting hot, it is...

    If it is turning orange and getting hot, it is one of two things. Either the drive device has no limiter or you have the wrong polarity for the LED. I suspect it is the wrong polarity but the fact...
  16. I always write my own assemblers. It is not that...

    I always write my own assemblers. It is not that hard. I do use Forth as one can repurpose the input parser used by the language. The assembler becomes the language. I usually write single pass...
  17. Replies
    28
    Views
    1,133

    Ok, don't leave us dangling, what did you do for...

    Ok, don't leave us dangling, what did you do for the coil? Your waveforms look good.

    Dwight
  18. Replies
    28
    Views
    1,133

    Input filter cores are a good source for such...

    Input filter cores are a good source for such toroidal cores. The wires you use can be small as the current needed for EPROM programming is generally quite small.
    Dwight
  19. The electrolytic capacitors are formed by a thin...

    The electrolytic capacitors are formed by a thin layer of aluminum oxide, formed in an electrolyte solution. When they have powered down for a long time, the oxide layer dissolves. Bringing the...
  20. Replies
    28
    Views
    1,133

    It is likely a schematic error, as with the pin...

    It is likely a schematic error, as with the pin numbering. I agree a power feed to the tap makes sense. The small turns would then do what is expected to oscillate, as feed back.
    Dwight
  21. Replies
    8
    Views
    497

    As a lot, the offered prices may not be close to...

    As a lot, the offered prices may not be close to the real value. It would be better to have some local collector broker the items for a percentage. I'm not the person you want as I'm on the other...
  22. Replies
    28
    Views
    1,133

    If your spice model doesn't include noise, it may...

    If your spice model doesn't include noise, it may never break into oscillation. You may need to give it an initial kick to start the oscillation. It needs to be enough to get the transistor into the...
  23. Replies
    28
    Views
    1,133

    The diagram shows no polarity dot of the...

    The diagram shows no polarity dot of the windings. The secondary can be ignored as it isn't need for the oscillation. I'd need to think about the winding polarities a while but I believe you are...
  24. Replies
    28
    Views
    1,133

    The regulation is slightly different on this...

    The regulation is slightly different on this board version but it is the same transformer, XT8K. The pins look to be numbered differently but they should still be wired the same. Your schematic shows...
  25. Replies
    28
    Views
    1,133

    Did he look at the diagram on: ...

    Did he look at the diagram on:

    http://www.s100computers.com/Hardware%20Manuals/Cromemco/Cromemco%20Bytesaver%20II%20023-0001%201978.pdf

    for the transformer?
    Dwight
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4