Image Map Image Map

Search:

Type: Posts; User: andromeda92

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    134
    Views
    25,496

    replace it and put it back the right way, or...

    replace it and put it back the right way, or unsolder it and solve it the right way
  2. Replies
    134
    Views
    25,496

    if it is in the wrong direction a capacitor...

    if it is in the wrong direction a capacitor explodes, if the polarities are inverted.
    On the XT-IDE card there is no inverted capacitor. What is your problem exactly?
  3. Replies
    134
    Views
    25,496

    here (https://imgur.com/mhF6o3e)and here ...

    here and

    here
  4. Replies
    134
    Views
    25,496

    DIP SWITCH for XT-IDE Rev 4 SW1 here...

    DIP SWITCH for XT-IDE Rev 4

    SW1 here

    SW2 here
  5. thank you for the link but it doesn't exist with...

    thank you for the link but it doesn't exist with another name, is amaquest AP8548.
  6. Any idea ?

    Any idea ?
  7. Manual or information for old 486 Amaquest AP8548 SiS 496/497

    Hi,
    Hello, I have an Amaquest AP8548 486 DX50 SiS 496/497 motherboard
    Characteristics:
    PCI-3, ISA 16bit-4 (NOT shared with PCI); SIMM 72-pin-4; IDE-2, Floppy-1, COM-2, LPT-1, PS / 2 (cable with...
  8. Hi, I have tested 3C509B-TPO on motherboard...

    Hi,
    I have tested 3C509B-TPO on motherboard AP8548 486 DX 50 sis 85C497, on ISA 16 bit with original software 3COM not modified.
    3C5X9CFG detect this card as 3C509-TPO, board is configued with...
  9. I received my 3C509B-TP. 3ccfg recognize my...

    I received my 3C509B-TP.

    3ccfg recognize my card as 3C509B-TP.
    I can disable plug and play
    3C509 0x60 work fine.
    I have IP address
    DHCP work fine.
    PING work fine.
    FTPSRV work fine.
  10. if someone has an image of a .hex file with an...

    if someone has an image of a .hex file with an IOBASE configuration: 320h irq 3 or 5 in isa mode, no modem, configport 110, XCVR: TP, with PNP Disabled, I can program the eeprom
    of my card.
    I have...
  11. also, the command 3CCFG configure /syncready is...

    also, the command 3CCFG configure /syncready is available only for the 3C509B-TPO in ISA mode.

    it's possible to modify configuration software 3ccfg for accept command ISA mod, for example...
  12. From the Test Menu, i have only: Run Test Test...

    From the Test Menu, i have only:
    Run Test
    Test Setup
    Echo Server

    On Menu Install:
    Menu Configure NIC, on I/O Address, i can only change address from 200-3E0

    3CCFG CONFIGURE /IOBASE:ISA <=...
  13. The NIC is installed on 8 bit ISA, from IBM 5155,...

    The NIC is installed on 8 bit ISA, from IBM 5155, this computer have not ISA 16 bit.

    The purpose of the modification was to use it on an xt such as IBM 5155 on 8 bit ISA.

    As soon as i receive...
  14. I have removed XT-IDE Card. I have put...

    I have removed XT-IDE Card.

    I have put 3C509B-TPO on another slot

    I have tested this two command:

    3CCFG CONFIGURE /IOBASE:320 /CONFIGPORT:110
    and
    3CCFG CONFIGURE /IOBASE:300 /CONFIGPORT:110
  15. I changed Address to 0x210 now because default is...

    I changed Address to 0x210 now because default is 0x300 and my XT-IDE is at 0x300.


    Diagnostic from group1 failed:

    Register Access Test: Passed
    EEPROM Vital Data Test: !Failed
    EEPROM...
  16. the command 3CCFG CONFIGURE /PNP:DISABLED not...

    the command 3CCFG CONFIGURE /PNP:DISABLED not work, i have the same message as above.

    I cannot put 0x110, in the configuration program 3ccfg, the address starts at 0x200.
    When I run 3CCFG...
  17. NO, is the same, No 3C509 Found. The probleme is...

    NO, is the same, No 3C509 Found.
    The probleme is not my XT-IDE Rev 4.1, it don't use IRQ and Address is 0x300 and block Address 0x308 that all,
    I have only CGA Card and Controller FDC for floppy....
  18. When i use your how to : 3CCFG.EXE CONFIGURE...

    When i use your how to :

    3CCFG.EXE CONFIGURE /int:3 /optimize:dos /modem:none /pnp:disabled /xcvr:auto

    it show:
    !!! ERROR !!! the configuration parameter specified is only available for...
  19. Replies
    4
    Views
    266

    DTP Scan port and STC Pin card ?

    Hi,
    What is DTP Scan port and STC Pin card on this link ?
    Thanks.
  20. if i put this card, i need to remove controller...

    if i put this card, i need to remove controller original FDC IBM ?
  21. thank you for your response.

    thank you for your response.
  22. hi, i have a 3C509B-TPO on my IBM 5155, when i...

    hi,
    i have a 3C509B-TPO on my IBM 5155, when i launch 3C509 0x60,
    it show No 3C509 Found.

    My network card is configured with 0x210 IRQ 5.

    I use 3C509.com modified for XT 8088 and 3ccfg.
    i...
  23. Replies
    134
    Views
    25,496

    transcend 2GB is ok but sandisk 128MB or sandisk...

    transcend 2GB is ok but sandisk 128MB or sandisk 512MB not work.
  24. [IBM 5155] 1.44 floppy drive controller card

    Hello,
    I wanted to know if this card worked on an IBM5155 to allow to put a 3.5 " 1.44 floppy drive.

    link

    i have already 3.5" floppy but only on 720k with original IBM FDC

    Thanks in advance.
  25. Hello, I have an ibm 5155 and a 3C509B-TPO...

    Hello,
    I have an ibm 5155 and a 3C509B-TPO etherlink III card. When I launch the modified 3ccfg configuration program, my card is recognized.

    I can modify the address and the irq then save it on...
Results 1 to 25 of 35
Page 1 of 2 1 2