Image Map Image Map
Page 2 of 2 FirstFirst 12
Results 11 to 12 of 12

Thread: VCF West VoIP BBS setup (ADIT 600)

  1. #11

    Default

    Hi trmg,
    I now have asterisk (16.2.1) and FreePBX (15.0.16.27) running on a system which detects my digium card (see below). I'm pretty new to this so I will be reading up on this for a while and don't expect any results soon. Any resources you can point me to would be much appreciated. Also please let me know if there are limitations to the hardware I selected. Thanks.

    dahdi_hardware -v
    pci:0000:02:08.0 wct4xxp+ d161:0220 Wildcard TE220 (4th Gen)

  2. #12

    Default

    Hi trmg,
    I think I am ready to ask for some help. What I have done so far:
    - got ADIT 600 configured for fxs_gs on ports 1-24 (I am not sure how to set 24 as d channel, it shows blinking green to indicate ringing?, my setup is pasted below), created an adapter to go from the telco connector pairs 1,2 to RJ11 (pair 1 connected to modem)
    - got Asterisk 16 and FreePBX 15 built
    - set up DAHDI trunk for channels 1-23
    - set up SIP trunk going to QuestBlue SBC

    Questions I have are:
    - how do I route calls to/from e.g. channel 1 on adit to go through QuestBlue trunk?
    - is it possible to have a pool for incoming calls, e.g. one DID goes to channel 1 then 2 on adit
    - is port 8 on last FXS module (channel 24) blinking green correct for d channel? is it used for anything in my configuration or should I configure all 24 channels as b channels?

    Thanks again for all your help and pointing me in the right direction.

    vm@telco:/etc/asterisk$ sudo dahdi_scan
    [1]
    active=yes
    alarms=OK
    description=T2XXP (PCI) Card 0 Span 1
    name=TE2/0/1
    manufacturer=Digium
    devicetype=Wildcard TE220 (4th Gen) (VPMOCT064)
    location=Board ID Switch 0
    basechan=1
    totchans=24
    irq=0
    type=digital-T1
    syncsrc=1
    lbo=0 db (CSU)/0-133 feet (DSX-1)
    coding_opts=B8ZS,AMI
    framing_opts=ESF,D4
    coding=B8ZS
    framing=ESF
    [2]
    active=yes
    alarms=RED/LFA
    description=T2XXP (PCI) Card 0 Span 2
    name=TE2/0/2
    manufacturer=Digium
    devicetype=Wildcard TE220 (4th Gen) (VPMOCT064)
    location=Board ID Switch 0
    basechan=25
    totchans=24
    irq=0
    type=digital-T1
    syncsrc=1
    lbo=0 db (CSU)/0-133 feet (DSX-1)
    coding_opts=B8ZS,AMI
    framing_opts=ESF,D4
    coding=B8ZS
    framing=ESF

    vm@telco:/etc/asterisk$ sudo dahdi_cfg -v
    DAHDI Tools Version - 3.1.0

    DAHDI Version: 3.1.0
    Echo Canceller(s): HWEC
    Configuration
    ======================

    SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1)
    SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1)

    48 channels to configure.

    Setting echocan for channel 1 to oslec
    Setting echocan for channel 2 to oslec
    Setting echocan for channel 3 to oslec
    Setting echocan for channel 4 to oslec
    Setting echocan for channel 5 to oslec
    Setting echocan for channel 6 to oslec
    Setting echocan for channel 7 to oslec
    Setting echocan for channel 8 to oslec
    Setting echocan for channel 9 to oslec
    Setting echocan for channel 10 to oslec
    Setting echocan for channel 11 to oslec
    Setting echocan for channel 12 to oslec
    Setting echocan for channel 13 to oslec
    Setting echocan for channel 14 to oslec
    Setting echocan for channel 15 to oslec
    Setting echocan for channel 16 to oslec
    Setting echocan for channel 17 to oslec
    Setting echocan for channel 18 to oslec
    Setting echocan for channel 19 to oslec
    Setting echocan for channel 20 to oslec
    Setting echocan for channel 21 to oslec
    Setting echocan for channel 22 to oslec
    Setting echocan for channel 23 to oslec
    Setting echocan for channel 24 to none
    Setting echocan for channel 25 to oslec
    Setting echocan for channel 26 to oslec
    Setting echocan for channel 27 to oslec
    Setting echocan for channel 28 to oslec
    Setting echocan for channel 29 to oslec
    Setting echocan for channel 30 to oslec
    Setting echocan for channel 31 to oslec
    Setting echocan for channel 32 to oslec
    Setting echocan for channel 33 to oslec
    Setting echocan for channel 34 to oslec
    Setting echocan for channel 35 to oslec
    Setting echocan for channel 36 to oslec
    Setting echocan for channel 37 to oslec
    Setting echocan for channel 38 to oslec
    Setting echocan for channel 39 to oslec
    Setting echocan for channel 40 to oslec
    Setting echocan for channel 41 to oslec
    Setting echocan for channel 42 to oslec
    Setting echocan for channel 43 to oslec
    Setting echocan for channel 44 to oslec
    Setting echocan for channel 45 to oslec
    Setting echocan for channel 46 to oslec
    Setting echocan for channel 47 to oslec
    Setting echocan for channel 48 to none

    vm@telco:/etc/asterisk$ cat /etc/dahdi/system.conf
    # Autogenerated by /usr/sbin/dahdi_genconf on Fri Jan 29 00:21:48 2010
    # If you edit this file and execute /usr/sbin/dahdi_genconf again,
    # your manual changes will be LOST.
    # Dahdi Configuration File
    #
    # This file is parsed by the Dahdi Configurator, dahdi_cfg
    #
    # Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER)
    span=1,1,0,esf,b8zs
    # termtype: te
    bchan=1-23
    dchan=24
    echocanceller=oslec,1-23

    # Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2"
    span=2,2,0,esf,b8zs
    # termtype: te
    bchan=25-47
    dchan=48
    echocanceller=oslec,25-47

    # Global data

    loadzone = us
    defaultzone = us

    vm@telco:/etc/asterisk$ cat chan_dahdi_channels_custom.conf
    ; Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) ESF/B8ZS ClockSource
    group=0,11
    context=from-pstn
    switchtype=national
    signalling=fxs_ls
    channel => 1-23
    ; context=from-analog
    group = 63

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •