Announcement

Collapse

Forum etiquette

Our mission ...

This forum is part of our mission to promote the preservation of vintage computers through education and outreach. (In real life we also run events and have a museum.) We encourage you to join us, participate, share your knowledge, and enjoy.

This forum has been around in this format for over 15 years. These rules and guidelines help us maintain a healthy and active community, and we moderate the forum to keep things on track. Please familiarize yourself with these rules and guidelines.


Remain civil and respectful

There are several hundred people who actively participate here. People come from all different backgrounds and will have different ways of seeing things. You will not agree with everything you read here. Back-and-forth discussions are fine but do not cross the line into rude or disrespectful behavior.

Conduct yourself as you would at any other place where people come together in person to discuss their hobby. If you wouldn't say something to somebody in person, then you probably should not be writing it here.

This should be obvious but, just in case: profanity, threats, slurs against any group (sexual, racial, gender, etc.) will not be tolerated.


Stay close to the original topic being discussed
  • If you are starting a new thread choose a reasonable sub-forum to start your thread. (If you choose incorrectly don't worry, we can fix that.)
  • If you are responding to a thread, stay on topic - the original poster was trying to achieve something. You can always start a new thread instead of potentially "hijacking" an existing thread.



Contribute something meaningful

To put things in engineering terms, we value a high signal to noise ratio. Coming here should not be a waste of time.
  • This is not a chat room. If you are taking less than 30 seconds to make a post then you are probably doing something wrong. A post should be on topic, clear, and contribute something meaningful to the discussion. If people read your posts and feel that their time as been wasted, they will stop reading your posts. Worse yet, they will stop visiting and we'll lose their experience and contributions.
  • Do not bump threads.
  • Do not "necro-post" unless you are following up to a specific person on a specific thread. And even then, that person may have moved on. Just start a new thread for your related topic.
  • Use the Private Message system for posts that are targeted at a specific person.


"PM Sent!" messages (or, how to use the Private Message system)

This forum has a private message feature that we want people to use for messages that are not of general interest to other members.

In short, if you are going to reply to a thread and that reply is targeted to a specific individual and not of interest to anybody else (either now or in the future) then send a private message instead.

Here are some obvious examples of when you should not reply to a thread and use the PM system instead:
  • "PM Sent!": Do not tell the rest of us that you sent a PM ... the forum software will tell the other person that they have a PM waiting.
  • "How much is shipping to ....": This is a very specific and directed question that is not of interest to anybody else.


Why do we have this policy? Sending a "PM Sent!" type message basically wastes everybody else's time by making them having to scroll past a post in a thread that looks to be updated, when the update is not meaningful. And the person you are sending the PM to will be notified by the forum software that they have a message waiting for them. Look up at the top near the right edge where it says 'Notifications' ... if you have a PM waiting, it will tell you there.

Copyright and other legal issues

We are here to discuss vintage computing, so discussing software, books, and other intellectual property that is on-topic is fine. We don't want people using these forums to discuss or enable copyright violations or other things that are against the law; whether you agree with the law or not is irrelevant. Do not use our resources for something that is legally or morally questionable.

Our discussions here generally fall under "fair use." Telling people how to pirate a software title is an example of something that is not allowable here.


Reporting problematic posts

If you see spam, a wildly off-topic post, or something abusive or illegal please report the thread by clicking on the "Report Post" icon. (It looks like an exclamation point in a triangle and it is available under every post.) This send a notification to all of the moderators, so somebody will see it and deal with it.

If you are unsure you may consider sending a private message to a moderator instead.


New user moderation

New users are directly moderated so that we can weed spammers out early. This means that for your first 10 posts you will have some delay before they are seen. We understand this can be disruptive to the flow of conversation and we try to keep up with our new user moderation duties to avoid undue inconvenience. Please do not make duplicate posts, extra posts to bump your post count, or ask the moderators to expedite this process; 10 moderated posts will go by quickly.

New users also have a smaller personal message inbox limit and are rate limited when sending PMs to other users.


Other suggestions
  • Use Google, books, or other definitive sources. There is a lot of information out there.
  • Don't make people guess at what you are trying to say; we are not mind readers. Be clear and concise.
  • Spelling and grammar are not rated, but they do make a post easier to read.
See more
See less

Need some help with 8 inch floppy drive...

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Need some help with 8 inch floppy drive...

    I'm about to aquire an IBM Displaywriter, with double floppy drive and no software. I do need to setup my old 286 PC to be able to read 8 inch floppies, so I guess I need some help.

    First - if I understand correctly, I can use (or create) and adapter from 34 pin floppy cable to 50 pin cable for 8 inch drive. I ordered this adapter:
    fdadap.jpg

    So far so good. Next, I do need 50 pin cable. Can these SCSI cables be used?
    s-l500.jpg

    Next - which drive can you reccomend? I need to be able to write both - DS/DD and SS/SD floppies, at least judging from IBM displaywriter specifications. I'm thinking about getting a Shugart SA 851.
    s-l1600.jpg

    Last - as I understand, the drive motor is directly powered with AC power, and control board needs 24V and 5V DC?

    Thanks in advance for any advice or help!

    #2
    # 1st
    The adapter is best. I have the older one. For SD format the floppy controller I prefer is

    Adaptec AHA-1522A then
    Adaptec AHA-1542B

    Look at Registry of mainboards/floppy controller results
    in http://classiccmp.org/dunfield/img/index.htm
    In the CP/M FAQ are some answers, here is a link as I don't want to post it all.

    Q14: Can I read my 8" disks with my PC?

    http://oldcomputers.dyndns.org/publi...ls/cpm-faq.txt

    What drives you may use ?
    I hope somebody other has an answer.

    # 2nd

    SCSI cable ?

    I believe so .

    Comment


      #3
      Originally posted by Adventurer View Post
      First - if I understand correctly, I can use (or create) and adapter from 34 pin floppy cable to 50 pin cable for 8 inch drive. I ordered this adapter:
      I use the D Bit FDADAP adapter as well. Note that it needs to be powered via the 4-pin connector.

      Originally posted by Adventurer View Post
      So far so good. Next, I do need 50 pin cable.
      To cater for the data connector on my TM848-02 drive, I use the FDADAP-to-drive cable shown at [here].

      Originally posted by Adventurer View Post
      Last - as I understand, the drive motor is directly powered with AC power, and control board needs 24V and 5V DC?
      My TM848-02 drive only needs +24 Vdc and +5 Vdc. I power it via the setup shown at [here].

      If you do not buy a tested drive, then do not be surprised if the drive is faulty. I had faulty capacitors in both of the drives that I purchased (separately).

      Having technical documentation for the drive is good as well (e.g. for jumper configuration, for repair).

      Don't accidentally buy a single-sided drive when you are after a double-sided one. That is what I did.

      Comment


        #4
        Originally posted by modem7 View Post
        If you do not buy a tested drive, then do not be surprised if the drive is faulty. I had faulty capacitors in both of the drives that I purchased (separately).

        Having technical documentation for the drive is good as well (e.g. for jumper configuration, for repair).

        Don't accidentally buy a single-sided drive when you are after a double-sided one. That is what I did.
        Thanks, a very useful information it is! I have bought (ordered) Shugart SA-851, which I guess is a double sided drive after all. Still, getting it to work might be an interesting task, since usually no one lists them as "working", at least for the fair price not. I know how to replace the capacitors, and do have a soldering station, however, I hope there might not be some mechanical damage to drive heads or something, which can not be repaired unless having one more drive.

        At least, so far:

        FDADAP adapter - ordered, on the way
        50 pin SCSI cable - ordered
        8 inch drive - Shugart SA-851 - ordered
        8 inch floppies - to be ordered
        DC adapter for 8 inch drive - to be bought
        286 PC with 5/14 floppy cables - in my possesion
        All available software images for an IBM Displaywriter already downloaded, including ImageDisk software as well
        Last, but not least - IBM Displaywriter, ordered, on the way, however, no documentation, no software provided.

        Am I missing something in order to transfer the data?

        Comment


          #5
          I would be interested to hear how this ends up working for you.

          I have successfully used the KryoFlux (USB floppy interface) to read 8" disks with a Shugart SA-800 single-sided drive and it worked fine. I haven't tried connecting the drive to a real PC though.

          You will likely need to adjust jumper settings on the Shugart drive to put it in PC-compatible mode (the factory default) if it has been changed to work with another type of computer. Some drives were made with soldered wire instead of jumpers so hopefully if you have one of these then it is already configured for PC operation.

          If you're using it with a standard PC floppy controller, make sure you get the right 50Hz/60Hz version for your local mains power. Where I live the mains is 50Hz and most drives for sale are 60Hz, likely because someone imported the wrong drive and is trying to sell it again when they discovered it didn't work. If you get the wrong drive then the motor will run at the wrong speed (assuming the voltage is compatible) but I think the KryoFlux might be able to compensate for this. A real PC controller can't, though.

          The FDADAP with SCSI cables works fine, as long as you can get the 50-pin edge connector at one end. The ones in your photo look fine. As well as +5VDC, +24VDC, and 240VAC @ 50Hz, my SA-800 also needs -5VDC to operate. The manuals can be found online and helpfully give part numbers for the various power connectors, along with current requirements for each voltage.

          Comment


            #6
            I went a bit over board with my setup but given that most of my drives are external it has proven to be quite versatile:

            FDADAP
            Current Wish List: 1. IBM 7531 Industrial Series PC 2. NEC MultiSync XL (JC-2001) Monitor 3. MicroSolutions UniDOS card 4. Compaq 14" VGA CRT Monitor (the one that came with the SystemPro). 5. Stacker HW CoProcessor Board MCA BUS. If you have any of the above for sale please PM me. Thank you!

            Comment


              #7
              Thanks everyone for advices and tips, and here are the news - I finally got all the components I needed, so I started to do some soldering/connecting job. The only problem - I had to use two power adapters for the drive, since local electronics shop did not have one with +24 and +5 V.

              At the beginning things looked pretty well...P1001331.jpg

              Later when the main connections and adapters were connected, it was time to connect FDDAP adapter and time to test the drive.

              P1001332.jpg

              Brand new old stock DS/DD floppies for testing:
              P1001333.jpg

              Test results:

              Motor working - OK
              Drive set up as 5.25 1.2 MB in BIOS - OK
              Access light lits when switching on the PC, drive solenoid makes a click - OK
              No errors on starting PC - OK
              Drive access, format: fail
              P1001334.jpg

              I did notice, that the rails are not moving - I can manually adjust them, and they just stay where they are. It seems there is a problem either with electronics, or the rail motor itself. Maybe I can not use it with an MS-DOS format? Even then I would expect the rails to move at least...

              Comment


                #8
                Forgot to write, that FDADAP adapter shows no progress when accessing drive - instead of track number there is "- -"

                Comment


                  #9
                  I had one 8" drive which did not move head assembly. One 74 TTL on board was dead. I would double check step pulses are there and are wide/slow enough for your particular drive. When that's OK it is time to study the schematics. At least make sure there is TTL high level on pin 36 - the STEP signal of the drive when it is powered on and idle.

                  EDIT: FDADAP staying in unknown state indicates there might be problem with Track0, STEP and DIRECTION signals. Check Track0 levels when you move head assembly by hand.

                  Comment


                    #10
                    What would be a good 8" drive that's cheap.
                    Building one might be a possibility if I can get the circuits.
                    - Liz Cray

                    Comment


                      #11
                      Originally posted by Adventurer View Post
                      ...
                      Test results:

                      Motor working - OK
                      Drive set up as 5.25 1.2 MB in BIOS - OK
                      Access light lits when switching on the PC, drive solenoid makes a click - OK
                      No errors on starting PC - OK
                      Drive access, format: fail
                      ...
                      The drive light should not light, nor should the HL solenoid engage until the drive is actually selected. Check the cable.
                      What drive number is the drive jumpered as?

                      m

                      Comment


                        #12
                        Originally posted by Adventurer View Post
                        Drive set up as 5.25 1.2 MB in BIOS - OK
                        Note for later when you get the drive operational.

                        1.2M drives have 80 tracks. Like my TM848, the SA-851 has 77 tracks.

                        From memory:
                        * When I used an XT-FDC card, and DOS tried to format/access tracks beyond 77 (because DOS thought there were 80), I would hear a very nasty sound from the drive.
                        * When I used an FDADAP, and DOS tried to format/access tracks beyond 77, the FDADAP appeared to keep the drive at track 77.

                        So with the FDADAP, when I formatted a floppy via DOS, track 77 on the floppy ended up being formatted four times, first as track 77, then as 78, then as 79, then as 80.
                        The result was that the last six tracks ended up being marked as ..., 72, 73, 74, 75, 76, 80.
                        This meant that only 76 tracks on the floppy were usable, and I had to hope that DOS would not try to put anything beyond track 76.

                        Comment


                          #13
                          Originally posted by sciencedude100 View Post
                          What would be a good 8" drive that's cheap.
                          Building one might be a possibility if I can get the circuits.
                          Building only the electronics you mean?

                          Comment


                            #14
                            I'm sure you know this already, but I'll say it anyway. On 8" floppies, unlike 5.25" floppies, you need a write enable tab over the write-protect slot. 5.25" are exactly the opposite.

                            Also, 3M produced a line of floppies packaged with transparent red write-enable tabs. Apparently, they're too transparent for some drives. That one took a bit of work to discover...

                            Comment


                              #15
                              Originally posted by archeocomp View Post
                              Building only the electronics you mean?
                              I can build (most likely) the mechanics of a drive and (definitely) the electronics.
                              All I would need are the components and schematics. I could even make my own board if needed.\
                              So, is there anyone with schematics of a DS/DD 8" floppy drive?
                              Also, what's a good reference on it's standards? (Such as speed, timings, data flow, etc.)
                              - Liz Cray

                              Comment

                              Working...
                              X