Announcement

Collapse

Forum Rules and Etiquette

Our mission ...

This forum is part of our mission to promote the preservation of vintage computers through education and outreach. (In real life we also run events and have a museum.) We encourage you to join us, participate, share your knowledge, and enjoy.

This forum has been around in this format for over 15 years. These rules and guidelines help us maintain a healthy and active community, and we moderate the forum to keep things on track. Please familiarize yourself with these rules and guidelines.


Rule 1: Remain civil and respectful

There are several hundred people who actively participate here. People come from all different backgrounds and will have different ways of seeing things. You will not agree with everything you read here. Back-and-forth discussions are fine but do not cross the line into rude or disrespectful behavior.

Conduct yourself as you would at any other place where people come together in person to discuss their hobby. If you wouldn't say something to somebody in person, then you probably should not be writing it here.

This should be obvious but, just in case: profanity, threats, slurs against any group (sexual, racial, gender, etc.) will not be tolerated.


Rule 2: Stay close to the original topic being discussed
  • If you are starting a new thread choose a reasonable sub-forum to start your thread. (If you choose incorrectly don't worry, we can fix that.)
  • If you are responding to a thread, stay on topic - the original poster was trying to achieve something. You can always start a new thread instead of potentially "hijacking" an existing thread.



Rule 3: Contribute something meaningful

To put things in engineering terms, we value a high signal to noise ratio. Coming here should not be a waste of time.
  • This is not a chat room. If you are taking less than 30 seconds to make a post then you are probably doing something wrong. A post should be on topic, clear, and contribute something meaningful to the discussion. If people read your posts and feel that their time as been wasted, they will stop reading your posts. Worse yet, they will stop visiting and we'll lose their experience and contributions.
  • Do not bump threads.
  • Do not "necro-post" unless you are following up to a specific person on a specific thread. And even then, that person may have moved on. Just start a new thread for your related topic.
  • Use the Private Message system for posts that are targeted at a specific person.


Rule 4: "PM Sent!" messages (or, how to use the Private Message system)

This forum has a private message feature that we want people to use for messages that are not of general interest to other members.

In short, if you are going to reply to a thread and that reply is targeted to a specific individual and not of interest to anybody else (either now or in the future) then send a private message instead.

Here are some obvious examples of when you should not reply to a thread and use the PM system instead:
  • "PM Sent!": Do not tell the rest of us that you sent a PM ... the forum software will tell the other person that they have a PM waiting.
  • "How much is shipping to ....": This is a very specific and directed question that is not of interest to anybody else.


Why do we have this policy? Sending a "PM Sent!" type message basically wastes everybody else's time by making them having to scroll past a post in a thread that looks to be updated, when the update is not meaningful. And the person you are sending the PM to will be notified by the forum software that they have a message waiting for them. Look up at the top near the right edge where it says 'Notifications' ... if you have a PM waiting, it will tell you there.

Rule 5: Copyright and other legal issues

We are here to discuss vintage computing, so discussing software, books, and other intellectual property that is on-topic is fine. We don't want people using these forums to discuss or enable copyright violations or other things that are against the law; whether you agree with the law or not is irrelevant. Do not use our resources for something that is legally or morally questionable.

Our discussions here generally fall under "fair use." Telling people how to pirate a software title is an example of something that is not allowable here.


Reporting problematic posts

If you see spam, a wildly off-topic post, or something abusive or illegal please report the thread by clicking on the "Report Post" icon. (It looks like an exclamation point in a triangle and it is available under every post.) This send a notification to all of the moderators, so somebody will see it and deal with it.

If you are unsure you may consider sending a private message to a moderator instead.


New user moderation

New users are directly moderated so that we can weed spammers out early. This means that for your first 10 posts you will have some delay before they are seen. We understand this can be disruptive to the flow of conversation and we try to keep up with our new user moderation duties to avoid undue inconvenience. Please do not make duplicate posts, extra posts to bump your post count, or ask the moderators to expedite this process; 10 moderated posts will go by quickly.

New users also have a smaller personal message inbox limit and are rate limited when sending PMs to other users.


Other suggestions
  • Use Google, books, or other definitive sources. There is a lot of information out there.
  • Don't make people guess at what you are trying to say; we are not mind readers. Be clear and concise.
  • Spelling and grammar are not rated, but they do make a post easier to read.
See more
See less

Cheapo IDE interface for Model 4p running MM CP/M

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Cheapo IDE interface for Model 4p running MM CP/M

    I finally finished the ide interface for my model 4p. The interface will support ide drives as well as CF. It basically is made out of 3 ls logic chips, some resistors and a few connectors. Here are the pictures.

    trs803.jpgtrs802.jpgtrs801.jpg

    Matt

    #2
    This is very interesting! Did you find the circuit on the web or design it yourself?

    What software trickery did you have to use to get it to recognize the HD on your 4P?

    Comment


      #3
      Yes, I found the circuit on the web and then made a few design changes to get it to work. I ended up writing two programs, An IDE Driver and a loader for the driver. The loader copies the driver into free memory past the cp/m bios and fcbs then re-writes the ramdrive sector read/write vector to point at the new driver. The loader also updates the DPB (disk parameter block) for the ramdrive to match a 5meg HD.

      I have a turbo Pascal program I wrote to do the formatting and disk/CF analysis.

      Seems to work great.

      Matt

      Comment


        #4
        So... did you leave the original HD configuration area alone?
        Normally a 64k Montezuma configuration does not have adequate room for a driver. Is is a 63k config or smaller?

        I already have a mfm-boot compatible IDE working, but I certainly am curious...

        Comment


          #5
          There is a little space in a 64k setup to place the driver I wrote. Fa81h-FF00h.

          You can see the version of the CP/M on the screen shot.

          Matt

          Comment


            #6
            Possible to provide schematics, Driver software etc. Looks a lot like the TRS-IDE project. Any info appreciated. Will it run TRS-DOS/LDOS?
            *FrankG*

            Comment


              #7
              I am not familiar with the TRS-IDE project but its entirely possible the HW design is very similar. I found a schematic on the web that needed minor tweaks to work. The modified interface should run under trs-dos/ldos and there are drivers for it around. I gave up on the trs-dos drivers when I was having issues with the HW and decided to switch to a grass roots approach with MM CP/M. I can try the trs-dos drivers again when I find another ide drive or CompactFlash. I must admit I am more interested in the CP/M aspect. I would add this thing doesn't hold a candle to the HW Emulator Ian developed. Ians thing is really the way to go.

              If someone can tell me an appropriate place for the SW I am happy to upload it. On the schematic it would probably be better if I describe the changes and let someone who is adept at schematic capture do the work.

              Matt

              Comment


                #8
                Is this the basis for it: http://www.qsl.net/zl1wjq/trside1.htm and can you tell me what components were added and where in the schematic. I notice more resistors and a transistor/Regulator? on 1 of the 2 dip header packages. And one header just appears to be just some 1k Resistors probably as pulls ups for the data bus or something? He also has a link to a modified TRSDOS 6 IDE drivers that should work with this. Yeah so f you can show where your components were added/changed would be helpful.
                *FrankG*

                Comment


                  #9
                  Frank, the changes are very simple and the good news is that not all the parts on the project board are wired up. The schematic you found is correct. Carefully notice how the author shows connections vs. jump overs. Also the pin numbering on the one I printed out is a little confusing. It's correct but some of the PIN numbers were running together.

                  Add 1k pull-ups to all the connected address lines and control lines coming in from the trs-80. I left the data bus as shown, no pull-ups. Parallel up the remaining open inverting buffers on u3b, pins 3 and 4. This will give the output a chance to pull down the 150 ohm resistor within the model 4p on the extiosel line. With just one buffer I noticed the voltage not dropping below the .7 volt threshold for a "low". Paralleling up buffers is not a great idea but it fixes the issue. I also added a 220 ohm pull down to u3b pin 4 (the output of the paralleled up buffers) to help with the biasing. Last items - add a 220 uf low esr electrolytic cap to the 5 volt rail on the project board. Make sure that all the ribbon cable ground lines coming from the model 4p are tied together at the project board and tied to the project board ground.

                  Matt
                  Last edited by FireBox; June 12, 2013, 05:04 PM.

                  Comment


                    #10
                    a couple of questions for clarification. When you say parallel up U3B Pin 3 & 4 what exactly do you mean? I'm a little confused here. One being an input the other an output. And the on pin 4 of U3B added a 220 Ohm pull down guess to ground. Also I do not add a 1k resistor to pin 43 extiosel cause this is tied to pin 4 of U3B correct? Sorry if dumb questions just want clarification.
                    Last edited by Chromedome45; June 12, 2013, 06:24 PM.
                    *FrankG*

                    Comment


                      #11
                      All good questions. Here is a pinout diagram for an ls04. In our case only 4 of the 6 inverting buffers are used. We can "parallel up" the remaining two buffers on the one that is being overloaded.

                      image.jpg

                      So pins 3,13,11 would be tied together and pins 4,12,10 would be tied together.

                      No pull-up for the extiosel as you suspected. The 220 pull down connects to pin 4 of the buffer

                      Comment


                        #12
                        Worth turning this into a PCB? It could have CompactFlash header or 40-pin header - or both.

                        Comment


                          #13
                          Got it thanks a lot. Sometimes I read to much into something. So essentially boosting the output. I agree with Pierce could possibly make a Ckt board out of it. I would say keep it simple and use an IDE header. Can always attach a IDE to CF adapter to it.

                          One more thing how big is the CF you are using smallest I have is a 2GB

                          So to recap all Address lines and most of the control lines are being pulled up through a 1k resistor to VCC except /EXTIOSEL. Line correct?
                          just really want to be sure.
                          *FrankG*

                          Comment


                            #14
                            How does this compare to FreHD?

                            Comment


                              #15
                              Simple TTL chips. Instead of a GAL & a PIC microcontroller. But IMO the FreHD is probably a better way to go. I am trying to build this up and test it out of curiosity. I have built up many projects before and all have worked. So just want to try it. Plus I have the chips available in my stash plus the connectors.
                              *FrankG*

                              Comment

                              Working...
                              X